What are the rules for Pinewood Derby?
All cars must pass the following inspection to qualify for the race:
- Width shall not exceed 2-3/4 inches.
- Length shall not exceed 7 inches.
- Weight shall not exceed 5 ounces.
- Axles, wheels, and body shall be from the materials provided in the kit.
- Wheel bearings, washers, and bushings are prohibited.
Where should the center of mass be on a Pinewood Derby car?
Putting Pinewood Derby® Car Weight randomly on your PWD car is not the key to getting the most out of your build. Center of gravity placement should be between 1⁄2″ – 1″ in front of the rear axle. This is true for all wheel base types. Whether you are using a standard wheelbase or an extended wheelbase.
Can you put weights on top of pinewood derby car?
When the paint has dried, mount the weight on the top of your car as far to the rear as possible. The weight should not extend past the rear of the car. Glue bottom weights to the bottom of the block to bring the total weight (including wheels and axles) to 5 oz.
Can Pinewood Derby car be less than 7?
Can a pinewood derby car be shorter than 7 inches? Yes, you can make your car shorter but it is not recommended. A shorter car will have a lower center of mass at the start so it will have less energy to convert into speed when going down the track.
Can you use duct tape on a pinewood derby car?
Please don’t use duct tape. Some of it is really gummy and you’ll have a terrible time getting it off not to mention it could get on the stop section then other cars.
Is it better to put weight on top or bottom of pinewood derby car?
To achieve this, place 2/5 of the added weight behind the rear axle, and the remaining 3/5 in front of the rear axle. Placing the weight lower on the car also gives greater stability.
How do you make a pinewood derby car go faster?
10 Tips and Tricks to a Fast and Cool-Looking Pinewood Derby Car
- Bake your block.
- Max out your weight at the regulation 5 ounces.
- Use all of the graphite (dry lubricant is usually allowed).
- Sand and polish your wheels and axles.
- Check alignment.
- Spend time on sanding.
- Use a high-quality paint.
- Add decals!
Do you glue pinewood derby axles?
7. Create Glue Holes: Glue the axles firmly in their holes to ensure that they stay perfectly placed, but make sure you don’t get glue on your wheels. 8. Add Weight: Remember to make your Pinewood Derby car as heavy as the rules allow.
Can you put stickers on pinewood derby cars?
Decals are an easy way to make your Pinewood Derby car look good. Most new decals are of the dry transfer type. They are very easy to use, just cut them out, peel them off then stick them on the car.
What are the rules of the pinewood derby?
Official Pinewood Derby Rules (Rules from BSA Pinewood Derby Kit) Car Dimension Rules The overall length of the car shall not exceed 7 inches. The overall width of the car shall not exceed 2 ¾ inches. The car must have 1 ¾” clearancebetween the wheels. The car must have 3/8” clearance underneath the body so it does not rub on the track.
How many Boy Scouts are in the Gulf Stream Council?
Gulf Stream Council, BSA The official website of the Gulf Stream Council, Boy Scouts of America which currently serves over 6800 Scouts and 2500 adult volunteers in a seven-county area including Palm Beach, Martin, St Lucie, Indian River, Glades, Okeechobee and Hendry counties in southeast Florida. Navigation Home
What are the rules for Pensacola Bay district Pinewood?
4 Pensacola Bay District PINEWOOD DERBY RULES II. CONSTRUCTION CONTINUED 9. Weights, washers, spacers, or bushings on the wheels are not allowed.
What are the dimensions of a pinewood derby car?
(Rules from BSA Pinewood Derby Kit) Car Dimension Rules. The overall length of the car shall not exceed 7 inches. The overall width of the car shall not exceed 2 ¾ inches. The car must have 1 ¾” clearance between the wheels. The car must have 3/8” clearance underneath the body so it does not rub on the.